• 0

Help: Toshiba Satellite C40D-A Can Not Install Os X
0

Question

good morning every one, i just want to ask if what is wrong with my installation of 10.8.2, i have successfully made a partition for my ML yet when it comes to 7 minutes before completion, a yellow triangle bust up my screen and tells me my installation has FAILED and i need to restart. 

 

I have used boot flags such as:

amd, -v -x npci=0x2000 GraphicsEnabler=No, I have combined them hoping I will have a successful one. Sometimes I got kernel panic especially when I remove the AMD kernel.

 

Lastly, i just want to inquire about the missing Kernel, the one after the Bootloader kext. 

 

Hope someone will help me. Below is my dxdiag copy paste of my laptop:

 

System Information
------------------
Time of this report: 12/22/2013, 04:24:05
       Machine name: KHASHYAH
   Operating System: Windows 8 Pro N 64-bit (6.2, Build 9200) (9200.win8_gdr.130108-1504)
           Language: English (Regional Setting: English)
System Manufacturer: TOSHIBA
       System Model: Satellite C40D-A
               BIOS: 1.00
          Processor: AMD E2-1800 APU with Radeon HD Graphics (2 CPUs), ~1.7GHz
             Memory: 2048MB RAM
Available OS Memory: 1604MB RAM
          Page File: 1255MB used, 2012MB available
        Windows Dir: C:Windows
    DirectX Version: DirectX 11
DX Setup Parameters: Not found
   User DPI Setting: Using System DPI
 System DPI Setting: 96 DPI (100 percent)
    DWM DPI Scaling: Disabled
     DxDiag Version: 6.02.9200.16384 64bit Unicode
 
isplay Devices
---------------
          Card name: Microsoft Basic Display Driver
       Manufacturer: (Standard display types)
          Chip type: 
           DAC type: 
        Device Type: Display-Only Device
         Device Key: EnumROOTBASICDISPLAY
     Display Memory: 256 MB
   Dedicated Memory: 0 MB
      Shared Memory: 256 MB
       Current Mode: 1366 x 768 (32 bit) (64Hz)
       Monitor Name: Generic Non-PnP Monitor
      Monitor Model: unknown
         Monitor Id: 
        Native Mode: unknown
        Output Type: Other
        Driver Name: 
System Devices
--------------
     Name: Network Controller
Device ID: PCIVEN_168C&DEV_0036&SUBSYS_061211AD&REV_014&3A4E89300A8
   Driver: n/a
 
     Name: PCI standard host CPU bridge
Device ID: PCIVEN_1022&DEV_1702&SUBSYS_00000000&REV_003&24116FE&0&C2
   Driver: n/a
 

 

Share this post


Link to post
Share on other sites

1 answer to this question

  • 0

this issues reminded me of 10.7.3

well, based on my experience, this was caused by how you customised the installation before choosing the drive installation location for the OSX.

Remember when you're being told to choose the drive installation location after do some partitioning using Disk Utility?, there's a little box on the left-bottom corner of the drive installation choice box, you click that and there, you HAVE to make sure that you don't tick them all, since it's not that need for all to be ticked.

 

If you're laptop VGA are already supported for hackintoshing, that you need to tick graphics enabler but don't tick the AMD or Nvidia ( if it's fully supported like mine ).

Then for the other options, you might wanna see in some forums like Tonymacx86, Niresh12495, Macbreakerand many more for the choices.

And for the other customisation like apps and so, don't tick it ( i did it ), they will do it for your system really soon after you finish the installation process and booted normally. :)

 

P/S : What are your system specs?

 

Regards 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
0