Niresh Kernel Panic After Installation (Boot Loop) - Troubleshooting - Hackintosh Zone Jump to content
  • 0
Sign in to follow this  
rpgall

Niresh Kernel Panic After Installation (Boot Loop)

Question

rpgall    1

Hey guys,

After i installed Niresh 10.8.5 i got the following kernel panic after i rebooted and tried to launch Niresh via the Bootloader from the installer USB.

Posted Image

I already tried bootflags like graphicsenabler and -x

Maybe its important that there is also Windows 8 on this PC

This are my specs:

Z68AP-D3

I7 2700k

ATI 7850

16 GB Ram

I hope someone of you can help me fix this annoying problem! Thank you

Share this post


Link to post
Share on other sites

2 answers to this question

Recommended Posts

  • 0
Niresh    2,309

Its Very Simple Make a USB Chameleon Using BootDiskUtility or

Use The Same USB but Remove The Kernel Flags on Clover Just Add -v

or If You Use Chameleon boot with -F -v GraphicsEnabler=Yes

Share this post


Link to post
Share on other sites
  • 0
rpgall    1

Thank you Niresh, awesome!

 

Now i'm stuck on 3 other problems:

 

I didn't managed to get the chameleon bootloader to  work, so i have no working bootloader anymore, except the usb stick with OSX 10.8.5. I tried to install it manually and with the chameleon wizard, after this i got only a boot 0: GPT - done error. I also don't know if chameleon is able to boot Windows 8 again or if i must look for another way. This is my SSD disk where both systems are installed:

 

 

dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *128.0 GB   disk1
   1:                        EFI                         209.7 MB   disk1s1
   2:                  Apple_HFS                         64.0 GB    disk1s2
   3:                  Apple_HFS OSX                     63.5 GB    disk1s3
 
I'll hope i find a way, because i really need both operation systems.
 
 
The second problem is that the 7850 ATI Radeon is the only 7xxx Card without native support, so i don't have any graphic acceleration, if i for example open a new tab in Safari, it is going crazy.. :)
 
I already tried to install this kext with the kext wizard, but i doesn't figured out, why it still doesnt work.. 
 
Also i didn't managed to get my sound working.. 
 
So if someone can help me also to fix this 3 little but big problems, i would be very happy.
 
Thank you. :-)
  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Download Hackintosh

  • Files

  • Posts

    • Hey!  I successfully installed macOS Sierra with the Version SierraAMD v3 on my AMD Pc.  But after setting up the PostInstall via Terminal, the OS stops booting at this line : ioconsoleusers: gioscreenlockstate 3, hs 0, bs 0, now 0, sm 0x0 Any solutions?    My System Specs: Mainboard: Asrock 970 Pro3 r2.0 Processor: AMD FX-6300 Graphics: Sapphire Radeon RX460 4GB   Thanks!
    • Ok, so I built a new hackintosh with Niresh Mavericks 10.9.0 on a modified Dell Precision T7400 and mostly everything seems to be working correctly except for two things: Sound (The obvious one), and Online video content (Youtube, Facebook videos, etc) play at lower than 1 fps, frozen speed, after 10 seconds of playback it reaches 4 seconds of elapsed time and I have found no other forums explaining this or talking about this so I decided to bring it up here. As for the sound situation, I already bought a new card to replace the X-FI, so yes, I am aware of the Sound Blaster Audigy X-FI Xtreme Audio not being supported, but what caught my attention is that the sound was working and video playback problem was gone temporarily, I happened to hear the sound from my headphones sitting on my desk and put them on, and sound. I decided to test a video on youtube, the problem with the videos, gone. But after a reboot, they were back. However I have the logs from today and can give them to whoever wants/needs them to figure out what may have caused the sound to kick in on the X-FI and maybe add support for this sound card. I copied as far back in the time that the system was on while sound was working that I could up to the shutdown event. I know it's pretty large but I am not sure where to look, I am simply handing this out to whoever wants to see what may have given me audio on this card for the session. From what I can see that looked to be the most closely related to my issue is something to do with bluetooth (I don't have bluetooth, btw), it says in console: "9/20/17 6:49:55.785 PM com.apple.audio.DriverHelper[200]: The plug-in named BluetoothAudioPlugIn.driver requires extending the sandbox for the mach service named com.apple.bluetoothaudiod." repeatedly many times. This could be completely unrelated.   The only recent actions I made that I personally can think of that may have triggered this would be: I installed several different versions of a music player through Winebottler and it failed to start, more and likely because of the lack of .net framework 2.0 and 4.0, this is my highest suspicion of being the likeliest cause, but I could be wrong. I installed Crossover and installed the music player in it, which it ran in and is where I discovered that you need .net 2.0 and 4.0 (It had the player in it's database and installed .net automatically) Ran Discord (It uses output/input, so may as well add that in) The player was MusicBee, and when it crashed, it also left a log that I could probably try to reproduce if needed.   Specs: Dell Precision T7400, 1x Intel Xeon x5482 Nvidia Geforce GTX 660 16GB ddr2 ram 667mhz (Tested to be working correctly, please don't ask me to run a mem test I am impatient enough as it is)
    • 980m+intel 530, 6820hk 512ssd+120ssd+1TB im trying to install macOsierra, and i tried a lot of combinations of arguments and configuration, nothing seems to work, i got the same problem every time ofter i start the installation! Is saying: System uptime in  nanoseconds: some random numbers.
    • Hello guys!


      Today I tried to install macOS High Sierra from a bootable usb, but my pc froze during the booting process.
      I need help. Can you help me?

      Here I attached a demo with the problem.
      https://goo.gl/cp5E8M


      Thanks in advance!
    • Hi, I am new at this, I installed maverick on a Lenovo g460 and everything ok but when I try to start appear a screen and say "system uptime in nanoseconds..." , I use -x and -x and others but I can't solve my problem. Sorry for my English. Thanks 
  • Download Statistics

    • Files
      842
    • Comments
      2,129
    • Reviews
      2,532

×